At 05:24 PM 2/22/98 -0700, you wrote:
>you need to ifconfig the local loopback.  I have no idea why this is
needed in
>1.3  but for some reason nothing works without it.
>
>ifconfig lo0 127.0.0.1
>
>That should fix it up.
>
>---
>Tim Rightnour    -  root@garbled.net
>http://www.zynetwc.com/~garbled/garbled.html

hrm... didnt seem to help, i see that the other end of the cat5 thats in the
hub doesnt make the hub light light up... and the light on the back of the
card
doesnt come on either :(

thanks
nick maniscalco

here are the messages while booting...

Loading netbsd.gz...
3723616+351632 [85]

Entering netbsd.gz at 0xfffffc0000300f30...
Unrecognized boot flag '-'.
Copyright (c) 1996, 1997 The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.3 (INSTALL) #0: Wed Dec 31 08:30:26 PST 1997
    cjs@bishop:/u1/cjs/co/branch/src/sys/arch/alpha/compile/INSTALL
Alpha PC AXPpci33 ("NoName"), 200MHz
8192 byte page size, 1 processor.
real mem = 67108864 (2072576 reserved for PROM, 65036288 used by NetBSD)
avail mem = 49561600
using 793 buffers containing 6496256 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21066 (pass 2)
lca0 at mainbus0
pci0 at lca0 bus 0
ncr0 at pci0 dev 6 function 0: ncr 53c810 fast10 scsi
ncr0: interrupting at isa irq 11
ncr0: minsync=25, maxsync=206, maxoffs=8, 16 dwords burst, normal dma fifo
ncr0: single-ended, open drain IRQ driver
ncr0: restart (scsi reset).
scsibus0 at ncr0: 8 targets
sd0 at scsibus0 targ 0 lun 0: <HP, 02439, 0LA4> SCSI2 0/direct fixed
sd0: sd0(ncr0:0:0): 10.0 MB/s (100 ns, offset 8)
1910MB, 2325 cyl, 19 head, 88 sec, 512 bytes/sect x 3912172 sectors
cd0 at scsibus0 targ 6 lun 0: <TOSHIBA, XM-4101TASUNSLCD, 1755> SCSI2
5/cdrom re
movable
sio0 at pci0 dev 7 function 0: vendor 0x8086 product 0x0484 (rev. 0x03)
de0 at pci0 dev 8 function 0
de0: interrupting at isa irq 5
de0: SMC 8432T 21040 [10Mb/s] pass 2.3
de0: address 00:00:c0:99:c0:0d
de0: enabling 10baseT port
de0: enabling AUI/BNC port
ahc0 at pci0 dev 11 function 0
ahc0: interrupting at isa irq 9
ahc0: aic7880 Wide Channel, SCSI Id=7, 16 SCBs
scsibus1 at ahc0 channel 0: 16 targets
ahc0: target 0 using 16Bit transfers
ahc0: target 0 synchronous at 10.0MHz, offset = 0x8
sd1 at scsibus1 targ 0 lun 0: <MICROP, 3387WS, x43h> SCSI2 0/direct fixed
sd1: 8296MB, 4811 cyl, 21 head, 168 sec, 512 bytes/sect x 16992188 sectors
de1 at pci0 dev 12 function 0
de1: interrupting at isa irq 10
de1: SMC 8432T 21040 [10Mb/s] pass 2.3
de1: address 00:00:c0:ae:93:0d
de1: enabling 10baseT port
de1: enabling AUI/BNC port
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
lpt0 at isa0 port 0x3bc-0x3bf irq 7
pcppi0 at isa0 port 0x60-0x64
pcprobe: reset error 1
pckbd0 at pcppi0
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
md0: internal 2048K image area
WARNING: can't figure what device matches "DVA 1 0 0 0 0 0 0"
root on md0a dumps on md0b
WARNING: clock gained 53 days -- CHECK AND RESET THE DATE!
root file system type: ffs
erase ^?, werase ^W, kill ^U, intr ^C

Welcome to the NetBSD 1.3 installation floppy.

enter "install" to install NetBSD,
      "upgrade" to upgrade an existing NetBSD system,
   or "shell" for a shell prompt.

your choice? shell