Re: kern/48058: bge(4) stops working after booting 5.2_STABLE

[Havard Eidnes <he%uninett.no@localhost>]

The following reply was made to PR kern/48058; it has been noted by GNATS.

From: Havard Eidnes <he%uninett.no@localhost>
To: msaitoh%NetBSD.org@localhost
Cc: gnats-bugs%netbsd.org@localhost
Subject: Re: kern/48058: bge(4) stops working after booting 5.2_STABLE
Date: Fri, 02 Aug 2013 12:29:13 +0200 (CEST)

 Hi,
 
 I now finally came around to booting 5.2 on the lab machine, and
 there it worked fine.  So it looks like the failure I experienced
 on that other IBM 306m is a sign of old age of the hardware.
 
 For the record, I attach the dmesg of the lab 306m.
 
 I guess we can just close this PR as a hardware fault.
 
 Regards,
 
 - Havard
 
 ------------------------------
 
 Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
     2006, 2007, 2008, 2009, 2010
     The NetBSD Foundation, Inc.  All rights reserved.
 Copyright (c) 1982, 1986, 1989, 1991, 1993
     The Regents of the University of California.  All rights reserved.
 
 NetBSD 5.2 (GENERIC) #0: Wed Nov 28 09:36:47 UTC 2012
         
builds%b8.netbsd.org@localhost:/home/builds/ab/netbsd-5-2-RELEASE/i386/201211280503Z-obj/home/builds/ab/netbsd-5-2-RELEASE/src/sys/arch/i386/compile/GENERIC
 total memory = 2046 MB
 avail memory = 1999 MB
 IBM IBM eServer 306m -[884930Y]- (IBM CORPORATION)
 mainbus0 (root)
 cpu0 at mainbus0 apid 0: Intel 686-class, 3200MHz, id 0xf43
 cpu1 at mainbus0 apid 1: Intel 686-class, 3200MHz, id 0xf43
 ioapic0 at mainbus0 apid 2
 acpi0 at mainbus0: Intel ACPICA 20080321
 npx1 at acpi0 (MATH, PNP0C04): io 0xf0-0xfe irq 13
 pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
 midi0 at pcppi1: PC speaker (CPU-intensive output)
 sysbeep0 at pcppi1
 attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0
 FWH (INT0800) at acpi0 not configured
 COM1 (PNP0501) at acpi0 not configured
 pckbc1 at acpi0 (KBC0, PNP0303) (kbd port): io 0x60,0x64 irq 1
 pckbc2 at acpi0 (MSE0, PNP0F13) (aux port): irq 12
 acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
 apm0 at acpi0: Power Management spec V1.2
 attimer1: attached to pcppi1
 pckbd0 at pckbc1 (kbd slot)
 pckbc1: using irq 1 for kbd slot
 wskbd0 at pckbd0 mux 1
 pms0 at pckbc1 (aux slot)
 pckbc1: using irq 12 for aux slot
 wsmouse0 at pms0 mux 0
 ipmi0 at mainbus0
 pci0 at mainbus0 bus 0: configuration mode 1
 pchb0 at pci0 dev 0 function 0
 pchb0: vendor 0x8086 product 0x2778 (rev. 0x81)
 ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x2779 (rev. 0x81)
 pci1 at ppb0 bus 1
 pci1: no spaces enabled!
 ppb1 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x01)
 pci2 at ppb1 bus 2
 ppb2 at pci2 dev 0 function 0: vendor 0x8086 product 0x032c (rev. 0x09)
 ppb2: disabling notification events
 pci3 at ppb2 bus 3
 vendor 0x8086 product 0x0326 (interrupt system, interface 0x20, revision 0x09) 
at pci2 dev 0 function 1 not configured
 ppb3 at pci0 dev 28 function 4: vendor 0x8086 product 0x27e0 (rev. 0x01)
 pci4 at ppb3 bus 4
 bge0 at pci4 dev 0 function 0: Broadcom BCM5721 Gigabit Ethernet
 bge0: interrupting at ioapic0 pin 16
 adjust device control 0x1a2100 -> 0x1a5100
 bge0: ASIC BCM5750 B1 (0x4101), Ethernet address 00:14:5e:82:10:fe
 brgphy0 at bge0 phy 1: BCM5750 1000BASE-T media interface, rev. 0
 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 ppb4 at pci0 dev 28 function 5: vendor 0x8086 product 0x27e2 (rev. 0x01)
 pci5 at ppb4 bus 5
 bge1 at pci5 dev 0 function 0: Broadcom BCM5721 Gigabit Ethernet
 bge1: interrupting at ioapic0 pin 17
 adjust device control 0x1a2100 -> 0x1a5100
 bge1: ASIC BCM5750 B1 (0x4101), Ethernet address 00:14:5e:82:10:ff
 brgphy1 at bge1 phy 1: BCM5750 1000BASE-T media interface, rev. 0
 brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x01)
 uhci0: interrupting at ioapic0 pin 23
 usb0 at uhci0: USB revision 1.0
 uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x01)
 uhci1: interrupting at ioapic0 pin 19
 usb1 at uhci1: USB revision 1.0
 uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x01)
 uhci2: interrupting at ioapic0 pin 18
 usb2 at uhci2: USB revision 1.0
 ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x01)
 ehci0: interrupting at ioapic0 pin 23
 ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
 usb3 at ehci0: USB revision 2.0
 ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0xe1)
 pci6 at ppb5 bus 10
 vga1 at pci6 dev 4 function 0: vendor 0x1002 product 0x515e (rev. 0x02)
 wsdisplay0 at vga1 kbdmux 1
 drm at vga1 not configured
 ichlpcib0 at pci0 dev 31 function 0
 ichlpcib0: vendor 0x8086 product 0x27b8 (rev. 0x01)
 ichlpcib0: 24-bit timer
 piixide0 at pci0 dev 31 function 1
 piixide0: Intel 82801GB/GR IDE Controller (ICH7) (rev. 0x01)
 piixide0: primary channel interrupting at ioapic0 pin 14
 atabus0 at piixide0 channel 0
 piixide0: secondary channel ignored (disabled)
 piixide1 at pci0 dev 31 function 2
 piixide1: Intel 82801GB/GR Serial ATA/Raid Controller (ICH7) (rev. 0x01)
 piixide1: using ioapic0 pin 19 for native-PCI interrupt
 atabus1 at piixide1 channel 0
 atabus2 at piixide1 channel 1
 ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x27da (rev. 0x01)
 ichsmb0: interrupting at ioapic0 pin 19
 iic0 at ichsmb0: I2C bus
 isa0 at ichlpcib0
 com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
 com0: console
 uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 atapibus0 at atabus0: 2 targets
 uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
 cd0 at atapibus0 drive 0: <HL-DT-ST  GCR-8240N, , 1.06> cdrom removable
 wd0 at atabus1 drive 0: <WDC WD2500JS-23MHB0>
 wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
 Kernelized RAIDframe activated
 pad0: outputs: 44100Hz, 16-bit, stereo
 audio0 at pad0: half duplex, playback, capture
 boot device: wd0
 root on wd0a dumps on wd0b
 root file system type: ffs