Subject: Re: kern/33047: fxp NICs are not useable on IBM Netfinity 4000R (no
To: None <firstname.lastname@example.org>
From: Timo Schoeler <email@example.com>
Date: 03/10/2006 16:56:59
Christos Zoulas schrieb:
> The following reply was made to PR kern/33047; it has been noted by GNATS.
> From: firstname.lastname@example.org (Christos Zoulas)
> To: email@example.com, firstname.lastname@example.org,
> email@example.com, firstname.lastname@example.org
> Subject: Re: kern/33047: fxp NICs are not useable on IBM Netfinity 4000R (no link)
> Date: Fri, 10 Mar 2006 10:48:23 -0500
> On Mar 10, 8:45am, email@example.com (firstname.lastname@example.org) wrote:
> -- Subject: kern/33047: fxp NICs are not useable on IBM Netfinity 4000R (no l
> | e100: Intel(R) PRO/100 Network Driver, 3.3.6-k2-NAPI
> | e100: Copyright(c) 1999-2004 Intel Corporation
> | e100: eth0: e100_probe: addr 0xfebff000, irq 9, MAC addr 00:06:29:DE:7C:29
> | e100: eth1: e100_probe: addr 0xfebfe000, irq 10, MAC addr 00:06:29:DE:7C:28
> | ---
> | NetBSD specific information (gathered via serial console, no typos! :)
> | *** ifconfig -a output ***
> | netbsd# ifconfig -a
> | fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
> | address: 00:06:29:de:87:39
> | media: Ethernet autoselect (none flowcontrol,rxpause,txpause)
> | status: no carrier
> | inet6 fe80::206:29ff:fede:8739%fxp0 prefixlen 64 scopeid 0x1
> | fxp0 at pci0 dev 17 function 0: i82559 Ethernet, rev 8
> | fxp0: interrupting at ioapic0 pin 18 (irq 10)
> | fxp0: Ethernet address 00:06:29:de:87:39
> | inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
> | inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> | fxp1 at pci0 dev 18 function 0: i82559 Ethernet, rev 8
> | fxp1: interrupting at ioapic0 pin 17 (irq 11)
> | fxp1: Ethernet address 00:06:29:de:87:38
> | inphy1 at fxp1 phy 1: i82555 10/100 media interface, rev. 4
> | inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> Is your ifconfig program old?
it's a NetBSD3-STABLE with patch for the Promise SATA300 HBA. ifconfig
is not older than the build. (i made an iso for this one.)
> What happens if you try to set the
> media manually?
i tried on both sides, on the switch and on the machine itself: same result.
today i put another fxp interface into the machine (into one of the two
PCI slots; the is populated by the SATA card) and turned off the second
serial port, thus freeing IRQ3. i pointed both onboard NICs to IRQ3 (as
they do when set to autoconfigure, which i also tried) and tried to use
the now as fxp2 known (pci) card.
interestingly, the handshake works and it has a link (Cisco 1924, 10MBit).
but it doesn't work: ping 184.108.40.206 (the machines' IP) goes into
nowhere, pinging the default gateway dito.
i then tried setting the same IP (220.127.116.11) on another machine in the
same subnet, which got recognized on the console!