I have rtk0 (onboard ethernet, does not work--"watchdog timeout"
errors), ral0 (PCI linksys WMP54g v4.1), and ral1 (USB Linksys WUSB54G
v4).

rtk0 at pci2 dev 2 function 0: Realtek 8139 10/100BaseTX
rtk0: interrupting at irq 11
rtk0: Ethernet address 00:16:76:91:aa:d5
rlphy0 at rtk0 phy 7: Realtek internal PHY

ral0 at pci2 dev 3 function 0: Ralink Technologies RT2561S 802.11b/g (rev. 0x00)
ral0: interrupting at irq 10
ral0: 802.11 address 00:16:b6:9a:fc:08
ral0: MAC/BBP RT2661b, RF RT2527
ral0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ral0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36M
bps 48Mbps 54Mbps
ral1 at uhub2 port 7
ral1: Cisco-Linksys Wireless-G USB Network Adapter, rev 2.00/0.04, addr 2
ral1: MAC/BBP RT2570 (rev 0x05), RF RT2526
ral1: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ral1: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36M
bps 48Mbps 54Mbps

NOTE: I'd like to fix rtk0 as well, as this machine may be my gateway.
 It works with GENERIC_LAPTOP on i386, but not on amd64--even with
ioapic disabled, ACPI enabled, ACPI_SCANPCI, and all of the *FIXUP
options.

IMHO, there should be an install kernel available for amd64 which
includes the following:

no options MPBIOS_SCANPCI
acpi0   at mainbus0
# To enable or disable ... ?
options ACPI_SCANPCI

# Maybe someday I can use the glorious hyperthreading
no options      MPBIOS
no ioapic*

I would like to use ioapic someday, as then I could use
hyperthreading.  However, if I enable it, my USB mouse does not work,
azalia0 output skips (sounds like IRQ conflict, brings back memories
of setting jumpers on my 8-bit soundblaster).

Sometimes I wish I still had to set jumpers for everything; at least
then it would all work!

--Blair

On 9/15/06, Francisco Valladolid Hdez. <ficovh@yahoo.com> wrote:
> --- Blair Sadewitz <blair.sadewitz@gmail.com> wrote:
>
> > I have a linksys WMP54G v4.1 card (RT2561S/RT2661b/
> > rt2527) (PCI).  I can "connect" to networks, that is
> > I can choose
> > available networks or it autodetects one.  However,
> > I cannot pass any
> > data, it seems (dhclient fails, cannot ping other
> > side, etc.)  I am
> > stymied by this and cannot figure out what to do.  a
> > USB ral adapter
> > works fine.
>
> How many network card have you installed ?
> >
> > Any ideas?
> > I am using 4.0_BETA from 9/10.  Please address all
> > correspondance to
> > me and not just to the list; thanks.
>
> it is importatn follow the thread, so many users with
> the same problem maybe solve it also.
>
> Regards.
> >
> >
> > --Blair
> >
>
>
> ____________________________________
> Fco.Valladolid Hdez.
> ficovh@yahoo.com
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam?  Yahoo! Mail has the best spam protection around
> http://mail.yahoo.com
>