I just rebuilt everything with sources from CVS on Thu Jun 29 22:27:51 
PDT 2006.  This kernel doesn't recognize the touchpad.  Dmesg (note no 
pms or wsmouse1; wsmouse0 is the scroll wheel on the SPIC) and relevant 
config lines below.  3.99.20 worked fine.  Has anyone else seen this?


pckbc*          at acpi?                # PC keyboard controller
#pckbc*         at pnpbios? index ?     # PC keyboard/mouse controller
pckbc0          at isa?                 # pc keyboard controller
pckbd*          at pckbc?               # PC keyboard
pms*            at pckbc?               # PS/2 mouse for wsmouse
#options        PMS_DISABLE_POWERHOOK   # Disable PS/2 reset on resume
options         PMS_SYNAPTICS_TOUCHPAD  # Enable support for Synaptics 
Touchpads
wsmouse*        at pms? mux 0


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 
2005, 2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.21 (CALLEBAUT) #10: Fri Jun 30 14:25:48 PDT 2006
        ed@callebaut.wing.org:/usr/src/arch/i386/obj/current/src/sys/arc
h/i386/compile/CALLEBAUT
total memory = 511 MB
avail memory = 495 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
timecounter: selected timecounter "i8254" frequency 1193182 Hz quality 
100
BIOS32 rev. 0 found at 0xfd890
PCI BIOS rev. 2.1 found at 0xfd9ca
pcibios: config mechanism [1][x], special cycles [x][x], last bus 2
PCI IRQ Routing Table rev. 1.0 found at 0xfdf50, size 144 bytes (7 
entries)
PCI Interrupt Router at 000:31:0 (Intel 82371FB (PIIX) PCI-ISA Bridge 
compatible)
------------------------------------------
  device vendor product pin PIRQ IRQ stage
------------------------------------------
000:29:0 0x8086 0x2482   A  0x00   9  0    already assigned
000:29:1 0x8086 0x2484   B  0x03   9  0    already assigned
002:05:0 0x1180 0x0476   A  0x05   3  0    already assigned
002:08:0 0x8086 0x1031   A  0x04   9  0    already assigned
------------------------------------------
mainbus0 (root)
pci_addr_fixup: 002:05:0 0x1180 0x0476 new address 0x20000000
pci_addr_fixup: 002:05:1 0x1180 0x0476 new address 0x20001000
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Mobile Pentium 4 (686-class), 1988.61 MHz, id 0xf27
cpu0: features bfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features bfebf9ff<PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX>
cpu0: features bfebf9ff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu0: features2 400<CID>
cpu0: "Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz"
cpu0: I-cache 12K uOp cache 8-way, D-cache 8 KB 64B/line 4-way
cpu0: L2 cache 512 KB 64B/line 8-way
cpu0: ITLB 4K/4M: 128 entries
cpu0: DTLB 4K/4M: 64 entries
cpu0: using thermal monitor 1
cpu0: 16 page colors
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <  SONY,      B0,20020801>, AslId <PTL ,00000000>
acpi0: SCI interrupting at int 9
acpitimer_test(): 10
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
timecounter: selected timecounter "ACPI-Fast" frequency 3579545 Hz 
quality 1000
ACPI-Fast 24-bit timer
acpi0: fixing up intr link \_SB_.LNKB
acpi0: fixing up intr link \_SB_.LNKC
acpi0: fixing up intr link \_SB_.LNKH
acpi0: fixing up intr link \_SB_.LNKF
acpi0: fixing up intr link \_SB_.LNKG
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
acpi: activated SNY6001
acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
PNP0A03 [PCI/PCI-X Host Bridge] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not 
configured
PNP0200 [AT DMA Controller] at acpi0 not configured
npx1 at acpi0 (PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: using exception 16
PNP0000 [AT Interrupt Controller] at acpi0 not configured
PNP0B00 [AT Real-Time Clock] at acpi0 not configured
pcppi1 at acpi0 (PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
attimer1 at acpi0 (PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
pckbc1 at acpi0 (PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (SNY9003): aux port
pckbc2: irq 12
acpiec0 at acpi0 (PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
acpibat0 at acpi0 (PNP0C0A-1): ACPI Battery (Control Method)
acpibat1 at acpi0 (PNP0C0A-2): ACPI Battery (Control Method)
acpiacad0 at acpi0 (ACPI0003): ACPI AC Adapter
com0 at acpi0 (PNP0501)
com0: io 0x3f8-0x3ff irq 4
com0: ns16550a, working fifo
lpt0 at acpi0 (PNP0401)
lpt0: io 0x378-0x37f,0x778-0x77f irq 7 drq 3
spic0 at acpi0 (SNY6001): Sony Programmable I/O Controller
spic0: io 0x1080-0x109f irq 11
wsmouse0 at spic0 mux 0
sony0 at acpi0 (SNY5001): Sony Miscellaneous Controller
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
acpitz0 at acpi0: ACPI Thermal Zone
acpitz0: unable to get polling interval; using default of 30.0s
acpitz0: passive cooling mode only
acpitz0: critical 89.9C passive 50.9C
pcppi1: attached to attimer1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82845 Host (rev. 0x04)
pchb0: random number generator enabled
agp0 at pchb0: aperture at 0xec000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: Intel 82845 AGP (rev. 0x04)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: ATI Technologies Radeon Mobility M7 LW 
(rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using 
wskbd0
wsmux1: connecting to wsdisplay0
uhci0 at pci0 dev 29 function 0: Intel 82801CA USB Controller (rev. 
0x02)
uhci0: interrupting at irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801CA USB Controller (rev. 
0x02)
uhci1: interrupting at irq 9
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801CA USB Controller (rev. 
0x02)
uhci2: interrupting at irq 9
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ppb1 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 
0x42)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
cbb0 at pci2 dev 5 function 0: Ricoh 5C476 PCI-CardBus bridge (rev. 
0xa8)
cbb0: using ioapic for interrupt
cbb1 at pci2 dev 5 function 1: Ricoh 5C476 PCI-CardBus bridge (rev. 
0xa8)
cbb1: using ioapic for interrupt
fwohci0 at pci2 dev 5 function 2: Ricoh 5C552 PCI-CardBus 
bridge/Firewire (rev. 0x00)
fwohci0: interrupting at irq 9
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 08:00:46:03:01:47:2a:31
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
M-s/]M-@ at ieee1394if0 not configured
fwohci0: Initiate bus reset
fxp0 at pci2 dev 8 function 0: Intel PRO/100 VE Network Controller, rev 
66
fxp0: interrupting at irq 9
fxp0: Ethernet address 08:00:46:7a:15:89
inphy0 at fxp0 phy 1: i82562ET 10/100 media interface, rev. 0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cbb0: interrupting at irq 9
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3
pcmcia0 at cardslot0
cbb1: interrupting at irq 9
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 4
pcmcia1 at cardslot1
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801CAM LPC Interface (rev. 0x02)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801CA IDE Controller (ICH3) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
Intel 82801CA SMBus Controller (SMBus serial bus, revision 0x02) at 
pci0 dev 31 function 3 not configured
auich0 at pci0 dev 31 function 5: i82801CA (ICH3) AC-97 Audio
auich0: interrupting at irq 9
auich0: ac97: Yamaha YMF753-S codec; 18 bit DAC, no 3D stereo
auich0: ac97: ext id 604<AC97_22,AMAP,SPDIF>
auich1 at pci0 dev 31 function 6: i82801CA (ICH3) AC-97 Modem
auich1: interrupting at irq 9
auich1: ac97: Conexant HSD11246 codec; no 3D stereo
auich1: ac97: ext mid 4009<CID1,LINE1>, secondary codec
auich1: codec not responding, status=0xff00
isa0 at pcib0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
isapnp0: no ISA Plug 'n Play devices found
WARNING: Callback scheduled before sysmon task queue thread present.
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
audio0 at auich0: full duplex, independent
Kernelized RAIDframe activated
IPsec: Initialized Security Association Processing.
spic0: v1=0x3b v2=0x00
wi0 at pcmcia0 function 0: <Lucent Technologies, WaveLAN/IEEE, Version 
01.01, >
wi0: 802.11 address 00:02:2d:4f:c5:13
wi0: using Sony WaveLAN/IEEE
wi0: Lucent Firmware: Station (6.16.1)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
umass0 at uhub2 port 1 configuration 1 interface 0
umass0: Sony USB Memory Stick Slot, rev 1.10/1.09, addr 2
umass0: using ATAPI over CBI with CCI
atapibus0 at umass0: 2 targets
sd0 at atapibus0 drive 0: <Sony, MSC-U03, 1.00> disk removable
sd0: drive offline
wd0 at atabus0 drive 0: <HTS721010G9AT00>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 95396 MB, 193821 cyl, 16 head, 63 sec, 512 bytes/sect x 195371568 
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) 
(using DMA)
atapibus1 at atabus1: 2 targets
cd0 at atapibus1 drive 0: <TOSHIBA DVD-ROM SD-R6012, , 1S31> cdrom 
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using 
DMA)
sd0(umass0:0:0):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

sd0(umass0:0:0):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

sd0(umass0:0:0):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

sd0(umass0:0:0):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

boot device: wd0
root on wd0a dumps on wd0b
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)


	--Ed


	--Ed