I haven't been building fresh -current kernels in a while, but decided
to try the latest to see how it would run.

I ran with a GENERIC; in the past, GENERIC has had problems (documented
elsehwere; mostly resolvable by disabling IOAPIC).  However, GENERIC has
been usable---I installed a first pass at NetBSD from GENERIC (though I
had to build a kernel before the system became very usable).

Now, however, it's much worse: The system appears to lock up during boot.
I can't be 100% sure; due to IOAPIC, the ethernet cards are rendered
useless.  The system gets to a 'login:' prompt on the local console and
then does not respond.  Whether the (USB) keyboard is another casulty
of IOAPIC or whether the whole system has locked up, I don't know.

All I could do was hit the power button.

Interestingly, when I pressed the front panel button, the system
flickered, once, but stayed on (unless I held the button down for
about 10 seconds, at which point the system shut down).  I don't
hit the power button very often, but I don't think that it should
flicker when I hit it; I think it should stay steadily on until
the button has been held for 10 seconds.  I haen't tried a recent
IOAPIC-less kernel, yet, but this seems worth reporting.  If the
INSTALL kernel "works" like this (or the installed GENERIC), then
the whole OS will be useless for people with systems like mine.


The rest of this email is the dmesg from an older -current kernel.
I can't send anything at all from the system under a -current
GENERIC built from yesterday's sources.  I can't remember the last
time that I tried a GENERIC; I only know that at one time GENERIC
worked well enough that I could get bootstrapped by building a
custom kernel.


NetBSD 3.99.3 (socrates) #0: Fri Apr  8 16:13:11 CDT 2005
	root@socrates:/usr/kernobj/usr/netbsd/current/src/sys/arch/amd64/compile/socrates
total memory = 511 MB
avail memory = 482 MB
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: AMD Athlon(tm) 64 Processor 3200+, 2009.26 MHz
cpu0: features: e7dbfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features: e7dbfbff<PGE,MCA,CMOV,PAT,PSE36,MPC,NOX,MMXX,MMX>
cpu0: features: e7dbfbff<FXSR,SSE,SSE2,LONG,3DNOW2,3DNOW>
cpu0: I-cache 64 KB 64B/line 2-way, D-cache 64 KB 64B/line 2-way
cpu0: L2 cache 1 MB 64B/line 16-way
cpu0: ITLB 32 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: 16 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Nvidia nForce3 Host-PCI bridge (rev. 0xa4)
pcib0 at pci0 dev 1 function 0
pcib0: Nvidia nForce3 PCI-ISA bridge (rev. 0xa6)
Nvidia nForce3 SMBus controller (SMBus serial bus, revision 0xa4) at pci0 dev 1 function 1 not configured
ohci0 at pci0 dev 2 function 0: Nvidia nForce3 USB Host Controller (rev. 0xa5)
ohci0: interrupting at irq 9
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Nvidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1 at pci0 dev 2 function 1: Nvidia nForce3 USB Host Controller (rev. 0xa5)
ohci1: interrupting at irq 9
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: Nvidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
Nvidia nForce3 USB2 Host Controller (USB serial bus, interface 0x20, revision 0xa2) at pci0 dev 2 function 2 not configured
auich0 at pci0 dev 6 function 0: nForce3 MCP-T AC-97 Audio
auich0: interrupting at irq 5
auich0: ac97: Avance Logic ALC658 codec; 20 bit DAC, 18 bit ADC, no 3D stereo
auich0: ac97: ext id 9c7<AC97_23,LDAC,SDAC,CDAC,SPDIF,DRA,VRA>
viaide0 at pci0 dev 8 function 0
viaide0: NVIDIA nForce3 IDE Controller (rev. 0xa5)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
ppb0 at pci0 dev 10 function 0: Nvidia nForce3 PCI-PCI bridge (rev. 0xa2)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
fxp0 at pci1 dev 9 function 0: i82558 Ethernet, rev 5
fxp0: interrupting at irq 11
fxp0: Enabling receiver lock-up workaround
fxp0: Ethernet address 00:03:47:72:7f:87
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rtk0 at pci1 dev 10 function 0: Realtek 8139 10/100BaseTX
rtk0: interrupting at irq 9
rtk0: Ethernet address 00:90:47:05:bc:75
ukphy0 at rtk0 phy 7: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000000, model 0x0000, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
re0 at pci1 dev 11 function 0: RealTek 8110S Single-chip Gigabit Ethernet
re0: interrupting at irq 5
re0: Ethernet address 00:0d:61:12:8b:5b
re0: using 256 tx descriptors
ukphy1 at re0 phy 7: Generic IEEE 802.3u media interface
ukphy1: RTL8169S/8110S 1000BASE-T media interface (OUI 0x00e04c, model 0x0011), rev. 0
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
Texas Instruments TSB43AA23 IEEE 1394 Host Controller (Firewire serial bus, interface 0x10) at pci1 dev 14 function 0 not configured
ppb1 at pci0 dev 11 function 0: Nvidia product 0x00d2 (rev. 0xa4)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
vga0 at pci2 dev 0 function 0: ATI Technologies Radeon 9200SE (rev. 0x01)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
pchb1 at pci0 dev 24 function 0
pchb1: Advanced Micro Devices AMD64 HyperTransport configuration (rev. 0x00)
pchb2 at pci0 dev 24 function 1
pchb2: Advanced Micro Devices AMD64 Address Map configuration (rev. 0x00)
pchb3 at pci0 dev 24 function 2
pchb3: Advanced Micro Devices AMD64 DRAM configuration (rev. 0x00)
pchb4 at pci0 dev 24 function 3
pchb4: Advanced Micro Devices AMD64 Miscellaneous configuration (rev. 0x00)
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
auich0: measured ac97 link rate at 47999 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Kernelized RAIDframe activated
uhub2 at uhub0 port 3
uhub2: NEC 2.0 hub, class 9/0, rev 2.00/1.00, addr 2
uhub2: 4 ports with 4 removable, self powered
uhidev0 at uhub1 port 3 configuration 1 interface 0
uhidev0: MONTEREY USB K/B WITH ACPI, rev 1.10/2.11, addr 2, iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub1 port 3 configuration 1 interface 1
uhidev1: MONTEREY USB K/B WITH ACPI, rev 1.10/2.11, addr 2, iclass 3/0
uhid0 at uhidev1: input=1, output=0, feature=0
uhidev2 at uhub2 port 4 configuration 1 interface 0
uhidev2: Logitech USB-PS/2 Optical Mouse, rev 2.00/11.10, addr 3, iclass 3/1
ums0 at uhidev2: 3 buttons and Z dir.
wsmouse0 at ums0 mux 0
wd0 at atabus0 drive 0: <WDC WD400BB-34DEA0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 38165 MB, 77542 cyl, 16 head, 63 sec, 512 bytes/sect x 78163247 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 1: <LG       DVD-ROM DRD-8160B, , 1.01> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(viaide0:1:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x50, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)