On Mon, May 24, 2004 at 03:55:01PM +0200, Manuel Bouyer wrote:
> On Sun, May 23, 2004 at 10:56:19PM +0200, Nicolas Joly wrote:
> > 
> > Hi,
> > 
> > I just upgraded my home PC (HP Pavilion 7825), to an up to date
> > -current (2.0E 20040523), and noticed that the ATAPI DVD-ROM is not
> > detected anymore.
> 
> Hi,
> can you set wdcdebug_mask to 0x10 and post the boot messages here ?
> You can do it this way: use boot -d, then at the db> prompt:
> write wdcdebug_mask 0x10

Sure, here it is :

viaide0:0: before reset, st0=0x50, st1=0x50
viaide0:1: before reset, st0=0x50, st1=0x50
viaide0:0:0: after reset, sc=0x1 sn=0x1 cl=0x0 ch=0x0
viaide0:0:1: after reset, sc=0x1 sn=0x1 cl=0x0 ch=0x0
viaide0:0: wdcwait_reset() end, st0=0x50 st1=0x50
viaide0:0: after reset, ret_value=0x3
viaide0:0:0: after reset, sc=0x1 sn=0x1 cl=0x0 ch=0x0
viaide0:0:1: after reset, sc=0x1 sn=0x1 cl=0x0 ch=0x0
viaide0:0: wait DRDY st0 0x50 st1 0x50
__wdcwait: timeout (time=11), status d0 error d0 (mask 0x0 bits 0x0)
__wdcwait: timeout (time=11), status d0 error d0 (mask 0x0 bits 0x0)
__wdcwait: timeout (time=11), status d0 error d0 (mask 0x0 bits 0x0)
atabusattach: ch_drive_flags 0x1 0x1
wd0 at atabus0 drive 0: <ST380021A>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd1 at atabus0 drive 1: <ST380021A>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA data transfers)
wd1(viaide0:0:1): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA data transfers)
viaide0:1:0: after reset, sc=0x80 sn=0x80 cl=0x80 ch=0x80
viaide0:1:1: after reset, sc=0x1 sn=0x1 cl=0x14 ch=0xeb
viaide0:1: wdcwait_reset() end, st0=0x80 st1=0x0
viaide0:1: after reset, ret_value=0x2
viaide0:1:1: after reset, sc=0x1 sn=0x1 cl=0x14 ch=0xeb
viaide0:1: wait DRDY st0 0x0 st1 0x0
atabusattach: ch_drive_flags 0x0 0x2
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 1: <CD-W58E, , 6.0A> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(viaide0:1:1): using PIO mode 4, DMA mode 2 (using DMA data transfers)
boot device: wd1

-- 
Nicolas Joly

Biological Software and Databanks.
Institut Pasteur, Paris.