Subject: current 1.6ZH: GENERIC_LAPTOP stops booting with Cardbus Card "Apaptec ADP-1480 SCSI" inserted
To: None <current-users@netbsd.org>
From: =?iso-8859-1?Q?Hilmar_B=F6hm?= <h.boehm@ndh.net>
List: current-users
Date: 01/18/2004 22:51:05
Is this card supported?
At least it seems to be supported, when I look into the GENERIC_LAPTOP
config file.
But when I insert this card, the kernel stop at this point:

----------------------------------------------------
Boot kernel messages - netbsd 1.6ZH - GENERIC_LAPTOP
-with Cardbus Card "Adaptec ADP-1480 SCSI loaded
- - - - - - - - - - - - - - - - - - - - - - - - - -
....
cardbus_read_exrom: bad header signature in ROM image 0: 0x0000
cardbus_attach_card: failed to read CIS
ahc0 at cardbus0 dev 0 function 0: Adaptec ADP-1480 SCSI
ahc0: interrupting at 11
uvm_fault)0xc05c5f00, 0, 0, 2) -> 0xe
kernel: page fault trap, code=0
stopped in pid 6.1 (cardslot0) at      netbsd:free+0x62:        movl
$0,0(%esi)
db>

db> tr
------

free(0,c057a800,2,ffffffff,0) at netbsd:free+0x62
ahc_check_extport(c2bcf000,cd1f24b4,b,0,10) at
netbsd:ahc_check_extport+0x1a9
ahc_cardbus_attach(c2be1f80,c2bcf000,cd1f2594,c2bcf38c,1) at
netbsd:ahc_cardbus_attach+0x207
config_attach(c2be1f80,c0571a44,cd1f2594,c040abe0,0) at
netbsd:config_attach+0x23c
cardbus_attach_card(c2be1f80,0,0,cd1de294,cd1d57f8) at
netbsd:cardbus_attach_card+0x441
cardslot_event_thread(c2781b80,66b000,674000,0,c010030c) at
cardslot_event_thread+x1d
db>
--------------------------------------------------------

(My system is a DELL notebook Inspiron 5150 / CPU-3.06GHz / Mem-2GB)
------------------

If I boot the same kernel without the card, the system comes up with no
problem.
"dmesg" output see below.

The kernel was built with the unmodified GENERIC_LAPTOP config file.

Is there a chance to get this working?

Regards. / Hilmar.

Btw: A NetBSD-1.6.2_RC3 GENERIC_LAPTOP kernel boots with the 1480B inserted,
but there is no SCSI dev configured.
-----
from dmesg:
ahc0 at cardbus0 dev 0 function 0: Adaptec ADP-1480 SCSI
ahc0: interrupting at 10
ahc0: CardBus device requires an SEEPROM
-----


---------------------------------
dmesg of the GENERIC_LAPTOP kernel boot and "1480B" not inserted:
- - - - - - - - - - - - - - - - - - - - - - - - - -

NetBSD 1.6ZH (LT) #0: Tue Jan 20 08:03:34 GMT 2004
	root@don097:/usr/src/sys/arch/i386/compile/LT
total memory = 2047 MB
avail memory = 1998 MB
BIOS32 rev. 0 found at 0xffe90
PCI BIOS rev. 2.1 found at 0xfcf1e
pcibios: config mechanism [1][x], special cycles [x][x], last bus 2
PCI IRQ Routing Table rev. 1.0 found at 0xfcb30, size 176 bytes (9 entries)
PCI Interrupt Router at 000:31:0 (Intel 82371MX Mobile PCI I/O IDE
Xcelerator (MPIIX))
------------------------------------------
  device vendor product pin PIRQ IRQ stage
------------------------------------------
000:29:0 0x8086 0x24c2   A  0x00  11  0    already assigned
000:29:1 0x8086 0x24c4   B  0x03  11  0    already assigned
000:29:2 0x8086 0x24c7   C  0x02  11  0    already assigned
000:31:1 0x8086 0x24ca   A  0x02  11  0    fixed up
000:31:5 0x8086 0x24c5   B  0x01  11  0    already assigned
000:31:6 0x8086 0x24c6   B  0x01  11  0    already assigned
002:01:0 0x14e4 0x4401   A  0x01  11  0    already assigned
002:02:0 0x14e4 0x4320   A  0x02  11  0    already assigned
002:04:0 0x104c 0xac44   A  0x00  11  0    already assigned
002:04:1 0x104c 0x8029   A  0x00  11  0    already assigned
------------------------------------------
PCI fixup examining 8086:3580
PCI fixup examining 8086:3584
PCI fixup examining 8086:3585
PCI fixup examining 8086:3581
PCI fixup examining 10de:324
PCI bridge 0: primary 0, secondary 1, subordinate 1
PCI fixup examining 8086:24c2
PCI fixup examining 8086:24c4
PCI fixup examining 8086:24c7
PCI fixup examining 8086:24cd
PCI fixup examining 8086:2448
PCI fixup examining 14e4:4401
PCI fixup examining 14e4:4320
PCI fixup examining 104c:ac44
PCI bridge 2: primary 2, secondary 3, subordinate 3
PCI fixup examining 104c:8029
PCI bridge 1: primary 0, secondary 2, subordinate 3
PCI fixup examining 8086:24cc
PCI fixup examining 8086:24ca
PCI fixup examining 8086:24c5
PCI fixup examining 8086:24c6
PCI bus #3 is the last bus
[System BIOS Setting]-----------------------
  device vendor product
  register space address    size
--------------------------------------------
000:00:0 0x8086 0x3580
	10h mem  0xe0000000 0x08000000
		[OK]
000:00:1 0x8086 0x3584
		[OK]
000:00:3 0x8086 0x3585
		[OK]
000:01:0 0x8086 0x3581
		[OK]
000:29:0 0x8086 0x24c2
	20h port 0x0000bf80 0x00000020
		[OK]
000:29:1 0x8086 0x24c4
	20h port 0x0000bf40 0x00000020
		[OK]
000:29:2 0x8086 0x24c7
	20h port 0x0000bf20 0x00000020
		[OK]
000:29:7 0x8086 0x24cd
	10h mem  0xf4fffc00 0x00000400
		[OK]
000:30:0 0x8086 0x2448
		[OK]
000:31:0 0x8086 0x24cc
		[OK]
000:31:1 0x8086 0x24ca
	10h port 0x000001f0 0x00000008
	14h port 0x000003f4 0x00000004
	18h port 0x00000170 0x00000008
	1ch port 0x00000374 0x00000004
	20h port 0x0000bfa0 0x00000010
	24h mem  0x00000000 0x00000400
		[NG]
000:31:5 0x8086 0x24c5
	10h port 0x0000b800 0x00000100
	14h port 0x0000bc40 0x00000040
	18h mem  0xf4fff800 0x00000200
	1ch mem  0xf4fff400 0x00000100
		[OK]
000:31:6 0x8086 0x24c6
	10h port 0x0000b400 0x00000100
	14h port 0x0000b080 0x00000080
		[OK]
001:00:0 0x10de 0x0324
	10h mem  0xfc000000 0x01000000
	14h mem  0xd0000000 0x10000000
		[OK]
002:01:0 0x14e4 0x4401
	10h mem  0xfaffe000 0x00002000
		[OK]
002:02:0 0x14e4 0x4320
	10h mem  0xfaffc000 0x00002000
		[OK]
002:04:0 0x104c 0xac44
	10h mem  0x00000000 0x00001000
		[NG]
002:04:1 0x104c 0x8029
	10h mem  0xfaffb800 0x00000800
	14h mem  0xfaff4000 0x00004000
		[OK]
--------------------------[  2 devices bogus]
 Physical memory end: 0x7ffcb000
 PCI memory mapped I/O space start: 0x80000000
[PCIBIOS fixup stage]-----------------------
  device vendor product
  register space address    size
--------------------------------------------
000:00:0 0x8086 0x3580
	10h mem  0xe0000000 0x08000000
		[OK]
000:00:1 0x8086 0x3584
		[OK]
000:00:3 0x8086 0x3585
		[OK]
000:01:0 0x8086 0x3581
		[OK]
000:29:0 0x8086 0x24c2
	20h port 0x0000bf80 0x00000020
		[OK]
000:29:1 0x8086 0x24c4
	20h port 0x0000bf40 0x00000020
		[OK]
000:29:2 0x8086 0x24c7
	20h port 0x0000bf20 0x00000020
		[OK]
000:29:7 0x8086 0x24cd
	10h mem  0xf4fffc00 0x00000400
		[OK]
000:30:0 0x8086 0x2448
		[OK]
000:31:0 0x8086 0x24cc
		[OK]
000:31:1 0x8086 0x24ca
	10h port 0x000001f0 0x00000008
	14h port 0x000003f4 0x00000004
	18h port 0x00000170 0x00000008
	1ch port 0x00000374 0x00000004
	20h port 0x0000bfa0 0x00000010
	24h mem  0x80000000 0x00000400
		[OK]
000:31:5 0x8086 0x24c5
	10h port 0x0000b800 0x00000100
	14h port 0x0000bc40 0x00000040
	18h mem  0xf4fff800 0x00000200
	1ch mem  0xf4fff400 0x00000100
		[OK]
000:31:6 0x8086 0x24c6
	10h port 0x0000b400 0x00000100
	14h port 0x0000b080 0x00000080
		[OK]
001:00:0 0x10de 0x0324
	10h mem  0xfc000000 0x01000000
	14h mem  0xd0000000 0x10000000
		[OK]
002:01:0 0x14e4 0x4401
	10h mem  0xfaffe000 0x00002000
		[OK]
002:02:0 0x14e4 0x4320
	10h mem  0xfaffc000 0x00002000
		[OK]
002:04:0 0x104c 0xac44
	10h mem  0x80001000 0x00001000
		[OK]
002:04:1 0x104c 0x8029
	10h mem  0xfaffb800 0x00000800
	14h mem  0xfaff4000 0x00004000
		[OK]
--------------------------[  0 devices bogus]
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium 4 (686-class), 3056.58 MHz, id 0xf29
cpu0: features bfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features bfebfbff<PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX>
cpu0: features bfebfbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu0: I-cache 12K uOp cache 8-way, D-cache 8 KB 64b/line 4-way
cpu0: L2 cache 512 KB 64b/line 8-way
cpu0: ITLB 4K/4M: 128 entries
cpu0: DTLB 4K/4M: 64 entries
cpu0: 16 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82855GM Host-to-Hub Controller (rev. 0x02)
agp0 at pchb0: can't find internal VGA device config space
Intel 82855GM GMCH Memory Controller (miscellaneous system, revision 0x02)
at pci0 dev 0 function 1 not configured
Intel 82855GM GMCH Configuration Process (miscellaneous system, revision
0x02) at pci0 dev 0 function 3 not configured
ppb0 at pci0 dev 1 function 0: Intel product 0x3581 (rev. 0x02)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: Nvidia Corporation product 0x0324 (rev. 0xa1)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
uhci0 at pci0 dev 29 function 0: Intel 82801DB/DBM USB UHCI Controller #1
(rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801DB/DBM USB UHCI Controller #2
(rev. 0x01)
uhci1: interrupting at irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801DB/DBM USB UHCI Controller #3
(rev. 0x01)
uhci2: interrupting at irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
Intel 82801DB/DBM USB EHCI Controller (USB serial bus, interface 0x20,
revision 0x01) at pci0 dev 29 function 7 not configured
ppb1 at pci0 dev 30 function 0: Intel 82801BAM Hub-to-PCI Bridge (rev. 0x81)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
bce0 at pci2 dev 1 function 0: Broadcom BCM4401 10/100 Ethernet
bce0: interrupting at irq 11
ukphy0 at bce0 phy 1: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000818, model 0x0036, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bce0: Ethernet address 00:0d:56:33:17:c2
Broadcom Corporation product 0x4320 (miscellaneous network, revision 0x02)
at pci2 dev 2 function 0 not configured
cbb0 at pci2 dev 4 function 0: Texas Instruments PCI4510 PCI-CardBus Bridge
w/ OHCI IEEE 1394 Controller (rev. 0x02)
Texas Instruments PCI4510 OHCI IEEE 1394 HOST Controller w/ PCI-CardBus
Bridge (Firewire serial bus, interface 0x10) at pci2 dev 4 function 1 not
configured
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3 device 0
pcmcia0 at cardslot0
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801DB ISA Bridge (rev. 0x01)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801DBM IDE Controller (ICH4-M) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
auich0 at pci0 dev 31 function 5: i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
auich0: interrupting at irq 11
auich0: ac97: SigmaTel STAC9750/51 codec; headphone, 20 bit DAC, 20 bit ADC,
SigmaTel 3D
auich0: ac97: ext id 601<AC97_22,AMAP,VRA>
Intel 82801DB/DBM AC97 Modem Controller (modem communications, revision
0x01) at pci0 dev 31 function 6 not configured
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
isapnp0: no ISA Plug 'n Play devices found
auich0: measured ac97 link rate at 35106 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
Kernelized RAIDframe activated
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <PHILIPS DVD+RW SDVD6004, , 1.03> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA
data transfers)
uhidev0 at uhub1 port 1 configuration 1 interface 0
uhidev0: vendor 0x1241 product 0x1155, rev 1.10/1.20, addr 2, iclass 3/1
ums0 at uhidev0: 5 buttons and Z dir.
wsmouse1 at ums0 mux 0
wd0 at atabus1 drive 0: <IC25N060ATMR04-0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 57231 MB, 116280 cyl, 16 head, 63 sec, 512 bytes/sect x 117210240
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA
data transfers)
boot device: wd0
root on wd0a dumps on wd0b
WARNING: possible botched superblock upgrade detected
on filesystem previously mounted on /
fs_bsize == fs_maxbsize (0x00002000) but FS_FLAGS_UPDATED is not set
Test your filesystem by running fsck_ffs -n -f on it.
If it reports:
``VALUES IN SUPER BLOCK DISAGREE WITH THOSE IN FIRST ALTERNATE''
you should be able to recover with fsck_ffs -b 32 -c 4
See the file src/UPDATING or
http://mail-index.netbsd.org/current-users/2004/01/11/0022.html
for more details
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
----------------------------------------------------------------------------
--