Hi *,

I have a Promise Serial ATA/150 TX2plus Bus Master IDE Accelerator
The drive is detected during POST and can be configured as RAID-1 component at BIOS level.
But NetBSD-current (20031011) always lists:

pdcide0 at pci0 dev 8 function 0
pdcide0: Promise Serial ATA/150 TX2plus Bus Master IDE Accelerator (rev. 0x02)
pdcide0: bus-master DMA support present
pdcide0: primary channel configured to compatibility mode
pdcide0: primary channel ignored (disabled)
pdcide0: secondary channel configured to compatibility mode
pdcide0: secondary channel ignored (disabled)

regardless whether RAID components are configured or not. Any
ideas how to access that disk, if possible.

Frank

dmesg output:
NetBSD 1.6ZC (SYSPIP_ISDN) #0: Sun Oct 12 10:40:22 MEST 2003
	kardel@pip:/src/NetBSD/netbsd/sys/arch/i386/compile/SYSPIP_ISDN
total memory = 1023 MB
avail memory = 943 MB
using 6144 buffers containing 52508 KB of memory
BIOS32 rev. 0 found at 0xf1aa0
mainbus0 (root)
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD K7 (Athlon) XP 2800+ (686-class), 2083.23 MHz, id 0x6a0
cpu0: features c3c3fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features c3c3fbff<PGE,MCA,CMOV,PAT,PSE36,MMXX,MMX>
cpu0: features c3c3fbff<FXSR,SSE,3DNOW2,3DNOW>
cpu0: I-cache 64 KB 64b/line 2-way, D-cache 64 KB 64b/line 2-way
cpu0: L2 cache 512 KB 64b/line 16-way
cpu0: ITLB 16 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries 4-way
cpu0: calibrating local timer
cpu0: apic clock running at 333 MHz
cpu0: 8 page colors
ioapic0 at mainbus0 apid 2 (I/O APIC)
ioapic0: pa 0xfec00000, version 3, 24 pins
ioapic0: misconfigured as apic 0
ioapic0: remapped to apic 2
acpi0 at mainbus0
acpi0: using Intel ACPI CA subsystem version 20030228
acpi0: X/RSDT: OemId <ASUS  ,A7V8X   ,42302e31>, AslId <MSFT,31313031>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
PNP0C01 at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0A03 at acpi0 not configured
PNP0C02 at acpi0 not configured
PNP0C02 at acpi0 not configured
PNP0000 at acpi0 not configured
PNP0200 at acpi0 not configured
PNP0100 at acpi0 not configured
PNP0B00 at acpi0 not configured
PNP0800 at acpi0 not configured
PNP0C04 at acpi0 not configured
PNP0700 at acpi0 not configured
PNP0401 at acpi0 not configured
PNP0501 at acpi0 not configured
PNP0501 at acpi0 not configured
PNP0303 at acpi0 not configured
PNPB02F at acpi0 not configured
PNP0C02 at acpi0 not configured
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: VIA Technologies VT8377 Apollo KT400 CPU to PCI Bridge (rev. 0x00)
agp0 at pchb0: aperture at 0xf8000000, size 0x10000000
ppb0 at pci0 dev 1 function 0: VIA Technologies VT8377 CPU-AGP Bridge (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: Matrox MGA G400 AGP (rev. 0x82)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
fwohci0 at pci0 dev 7 function 0: VIA Technologies VT3606 OHCI IEEE 1394 Controller (rev. 0x80)
fwohci0: interrupting at ioapic0 pin 17 (irq 10)
fwohci0: OHCI 1.0, 00:e0:18:00:00:0e:37:67, 400Mb/s, 2048 max_rec, 4 ir_ctx, 8 it_ctx
pdcide0 at pci0 dev 8 function 0
pdcide0: Promise Serial ATA/150 TX2plus Bus Master IDE Accelerator (rev. 0x02)
pdcide0: bus-master DMA support present
pdcide0: primary channel configured to compatibility mode
pdcide0: primary channel ignored (disabled)
pdcide0: secondary channel configured to compatibility mode
pdcide0: secondary channel ignored (disabled)
bge0 at pci0 dev 9 function 0: Broadcom BCM5702X Gigabit Ethernet
bge0: interrupting at ioapic0 pin 18 (irq 5)
bge0: ASIC BCM5703 A2, Ethernet address 00:e0:18:dd:34:6f
brgphy0 at bge0 phy 1: BCM5703 1000BASE-T media interface, rev. 2
brgphy0: using BCM5703 DSP patch
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
isic0 at pci0 dev 10 function 0: ELSA QuickStep 1000pro/PCI
isic0: IPAC PSB2115 Version 1.1
isic0: interrupting at ioapic0 pin 16 (irq 11)
ISDN 0 at isic0, 2 B channels
ex0 at pci0 dev 11 function 0: 3Com 3c905B-TX 10/100 Ethernet (rev. 0x30)
ex0: interrupting at ioapic0 pin 19 (irq 9)
ex0: MAC address 00:10:5a:d8:53:54
exphy0 at ex0 phy 24: 3Com internal media interface
exphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ahc0 at pci0 dev 12 function 0
ahc0: interrupting at ioapic0 pin 19 (irq 9)
ahc0: aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
scsibus0 at ahc0: 16 targets, 8 luns per target
ex1 at pci0 dev 14 function 0: 3Com 3c905C-TX 10/100 Ethernet with mngmt (rev. 0x6c)
ex1: interrupting at ioapic0 pin 17 (irq 10)
ex1: MAC address 00:50:da:ee:ca:2e
bmtphy0 at ex1 phy 24: Broadcom 3c905C internal PHY, rev. 4
bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
uhci0 at pci0 dev 16 function 0: VIA Technologies VT83C572 USB Controller (rev. 0x80)
uhci0: interrupting at ioapic0 pin 21 (irq 9)
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 16 function 1: VIA Technologies VT83C572 USB Controller (rev. 0x80)
uhci1: interrupting at ioapic0 pin 21 (irq 9)
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 16 function 2: VIA Technologies VT83C572 USB Controller (rev. 0x80)
uhci2: interrupting at ioapic0 pin 21 (irq 9)
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
VIA Technologies VT8237 EHCI USB Controller (USB serial bus, interface 0x20, revision 0x82) at pci0 dev 16 function 3 not configured
pcib0 at pci0 dev 17 function 0
pcib0: VIA Technologies VT8235 (Apollo KT400) PCI-ISA Bridge (rev. 0x00)
viaide0 at pci0 dev 17 function 1
viaide0: VIA Technologies VT8235 ATA133 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus1 at viaide0 channel 1
auvia0 at pci0 dev 17 function 5: VIA VT8235 AC'97 Audio (rev 0x50)
auvia0: interrupting at ioapic0 pin 22 (irq 9)
auvia0: ac97: Avance Logic ALC650 codec; 20 bit DAC, 18 bit ADC, Realtek 3D
auvia0: ac97: ext id 5c7<AC97_22,LDAC,SDAC,CDAC,SPDIF,DRA,VRA>
audio0 at auvia0: full duplex, mmap, independent
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsprobe: reset error 5
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
ioapic0: enabling
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
raidattach: Asked for 8 units
Kernelized RAIDframe activated
vinum: loaded
IPsec: Initialized Security Association Processing.
fw0 at fwohci0: 00:e0:18:00:00:0e:37:67:0a:02:ff:ff:f0:01:00:00
scsibus0: waiting 2 seconds for devices to settle...
wd0 at atabus0 drive 0: <IC35L060AVER07-0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 58644 MB, 119150 cyl, 16 head, 63 sec, 512 bytes/sect x 120103200 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd1 at atabus0 drive 1: <IBM-DTLA-305040>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 39266 MB, 79780 cyl, 16 head, 63 sec, 512 bytes/sect x 80418240 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA data transfers)
wd1(viaide0:0:1): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA data transfers)
wd2 at atabus1 drive 0: <IC35L120AVV207-1>
wd2: drive supports 16-sector PIO transfers, LBA48 addressing
wd2: 115 GB, 239340 cyl, 16 head, 63 sec, 512 bytes/sect x 241254720 sectors
wd2: 32-bit data port
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd3 at atabus1 drive 1: <IBM-DTTA-351010>
wd3: drive supports 16-sector PIO transfers, LBA addressing
wd3: 9671 MB, 19650 cyl, 16 head, 63 sec, 512 bytes/sect x 19807200 sectors
wd3: 32-bit data port
wd3: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
wd2(viaide0:1:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA data transfers)
wd3(viaide0:1:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
uhub0: port error, restarting port 1
uhub0: port error, giving up port 1
uhub0: port error, restarting port 2
uhub0: port error, giving up port 2
uhub1: port error, restarting port 1
uhub1: port error, giving up port 1
uhub1: port error, restarting port 2
uhub1: port error, giving up port 2
uhub2: port error, restarting port 1
uhub2: port error, giving up port 1
uhub2: port error, restarting port 2
uhub2: port error, giving up port 2
uhub3 at uhub0 port 2
uhub3: Texas Instruments UT-USB41 hub, class 9/0, rev 1.10/1.10, addr 2
uhub3: 4 ports with 4 removable, self powered
uhidev0 at uhub3 port 1 configuration 1 interface 0
uhidev0: Microsoft Microsoft IntelliMouse M-. with IntelliEye, rev 1.10/1.01, addr 3, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse0 at ums0 mux 0
cd0 at scsibus0 target 5 lun 0: <YAMAHA, CRW-F1S, 1.0g> cdrom removable
cd0: sync (50.00ns offset 15), 8-bit (20.000MB/s) transfers
st0 at scsibus0 target 8 lun 0: <SONY, SDT-10000, 0101> tape removable
st0: drive empty
st0: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers
umodem0 at uhub3 port 2 configuration 2 interface 0
umodem0: Lucent Technologies, Inc. ELSA Modem Board, rev 1.00/1.00, addr 4, iclass 2/2
umodem0: data interface 1, has CM over data, has break
umodem0: status change notification available
ucom0 at umodem0
Searching for RAID components...
boot device: wd1
root on wd1a dumps on wd1b
mountroot: trying smbfs...
mountroot: trying coda...
mountroot: trying msdos...
mountroot: trying cd9660...
mountroot: trying ntfs...
mountroot: trying nfs...
mountroot: trying lfs...
mountroot: trying ext2fs...
mountroot: trying ffs...
root file system type: ffs
init: copying out path `/sbin/init' 11
IP Filter: v3.4.29 initialized.  Default = block all, Logging = enabled