This was working fine on the AXPPCI 3.x firmware, but I think I just
shot myself in the foot by updating it. The RealTek PCI ethernet card is
working (albiet slowly, ~300k/sec on 10BaseT) and the pci config space seems
to be valid for the pci HB. Can this be fixed in software, or do I need to
reflash back to something earlier? I also haven't updated the Firmware on
the card (made by SIIG), but I don't invision that causing a problem. The
secondary channel is disabled because I don't have anything plugged into it.
I can plug another drive in there if someone wants to be sure the same thing
happens on both channels.


    Chris


[ preserving 448536 bytes of netbsd ELF symbol table ]
consinit: not using prom console
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.5.1_BETA2 (GENERIC) #29: Wed May 16 01:24:39 MEST 2001
    he@albatross.runit.no:/usr/src/sys/arch/alpha/compile/GENERIC
Alpha PC AXPpci33, 166MHz
8192 byte page size, 1 processor.
total memory = 32768 KB
(2016 KB reserved for PROM, 30752 KB used by NetBSD)
avail memory = 23016 KB
using 205 buffers containing 1640 KB of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), LCA-2 (21066 pass 2)
lca0 at mainbus0
pci0 at lca0 bus 0
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
siop0 at pci0 dev 6 function 0: Symbios Logic 53c810 (fast scsi)
siop0: interrupting at isa irq 11
scsibus0 at siop0: 8 targets, 8 luns per target
sio0 at pci0 dev 7 function 0: Intel 82378ZB System I/O (SIO) (rev. 0x03)
rtk0 at pci0 dev 11 function 0: RealTek 8139 10/100BaseTX
rtk0: interrupting at isa irq 5
rtk0: Ethernet address 00:a0:4b:0f:78:5e
ukphy0 at rtk0 phy 7: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000000, model 0x0000, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pciide0 at pci0 dev 12 function 0: Triones/Highpoint HPT366 IDE Controller
pciide0: bus-master DMA support present
pciide0: primary channel wired to native-PCI mode
pciide0: using isa irq 9 for native-PCI interrupt
pciide0: couldn't map primary channel cmd regs
pciide1 at pci0 dev 12 function 1pciide1: device disabled (at device)
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
vga0 at isa0 port 0x3b0-0x3df iomem 0xa0000-0xbffff
wsdisplay0 at vga0
lpt0 at isa0 port 0x3bc-0x3bf irq 7
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
isabeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <COMPAQPC, ST32430N, 0554> SCSI2 0/direct
fixed
siop0: target 0 now synchronous at 10.0Mhz, offset 8
sd0: 2006 MB, 3992 cyl, 9 head, 114 sec, 512 bytes/sect x 4110000 sectors
cd0 at scsibus0 target 4 lun 0: <PIONEER, CD-ROM DR-U12X, 1.06> SCSI2
5/cdrom removable
siop0: target 4 now synchronous at 10.0Mhz, offset 8
root on sd0a dumps on sd0b
root file system type: ffs