Subject: usb zip drive:( -> weekly usb question
To: None <>
From: mel kravitz <>
List: current-users
Date: 01/01/2000 11:18:49
This is a multi-part message in MIME format.
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit

I have 1.4P current 12/25 running on a Toshiba 8000, with a 4 port usb
hub, HP 970Cse and Iomega zip drive,
i can print fine using /dev/ulpt0, however i don't seem to be able to
mount  /dev/sd0d /mnt i get 'device not ready'
message , i can not read its <disklabel  -e  /dev/sd0> . I can mount
this disk on a buddies Toshiba 3010 -same 12/25
source? dmesg below, any help would be welcome.

Content-Type: text/plain; charset=us-ascii;
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;

NetBSD 1.4P (NEW) #0: Fri Dec 31 23:27:58 PST 1999
cpu0: family 6 model 5 step 2
cpu0: Intel Pentium II (Deschutes) (686-class)
total memory = 127 MB
avail memory = 115 MB
using 1658 buffers containing 6632 KB of memory
BIOS32 rev. 0 found at 0xfc500
PCI BIOS rev. 2.1 found at 0xfedce
pcibios: config mechanism [1][x], special cycles [x][x], last bus 21
PCI IRQ Routing Table rev. 1.0 found at 0xf01c0, size 128 bytes (6 entries)
PCI Interrupt Router at 000:05:0 (Intel 82371FB PCI-to-ISA Bridge (PIIX))
  device vendor product pin PIRQ   IRQ stage
000:04:0 0x10c8 0x0005  A   0x02   11  0
000:05:2 0x8086 0x7112  D   0x03   11  0
000:09:0 0x1179 0x0701  A   0x02   11  0
000:11:0 0x1179 0x060a  A   0x00   11  0
000:11:1 0x1179 0x060a  B   0x01   11  0
PCI bridge 0: primary 0, secondary 1, subordinate 1
PCI bridge 1: primary 0, secondary 2, subordinate 2
PCI bus #2 is the last bus
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82443BX Host Bridge/Controller (AGP disabled) (rev. 0x02)
vga1 at pci0 dev 4 function 0: Neomagic MagicMedia 256AV VGA (rev. 0x12)
wsdisplay0 at vga1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 5 function 0
pcib0: Intel 82371AB PCI-to-ISA Bridge (PIIX4) (rev. 0x02)
pciide0 at pci0 dev 5 function 1: Intel 82371AB IDE controller (PIIX4)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <HITACHI_DK227A-50>
wd0: drive supports 16-sector pio transfers, lba addressing
wd0: 4789MB, 10380 cyl, 15 head, 63 sec, 512 bytes/sect x 9809100 sectors
wd0: 32-bits data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data transfers)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1
cd0 at atapibus0 drive 0: <CD-224E, , 7.5A> type 5 cdrom removable
cd0: 32-bits data port
cd0: drive supports PIO mode 4, DMA mode 2
pciide0: secondary channel interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
uhci0 at pci0 dev 5 function 2: Intel 82371AB USB Host Controller (PIIX4) (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at uhub0 port 1
uhub1: Texas Instruments UT-USB41 hub, class 9/0, rev 1.00/1.00, addr 2
uhub1: 4 ports with 4 removable, self powered
umass0 at uhub1 port 1 configuration 1 interface 0
umass0: Iomega USB Zip 100, rev 1.10/1.00, addr 3
umass0: SCSI over Bulk-Only (iclass 8/6/80)
scsibus0 at umass0: 2 targets, 1 luns per target
ulpt0 at uhub1 port 2 configuration 1 interface 0
ulpt0: Hewlett-Packard DeskJet 970C, rev 1.00/1.00, addr 4, iclass 7/1
Intel 82371AB Power Management Controller (PIIX4) (miscellaneous bridge, revision 0x02) at pci0 dev 5 function 3 not configured
Toshiba America Info Systems Fast Infrared Type O (miscellaneous communications, revision 0x23) at pci0 dev 9 function 0 not configured
cbb0 at pci0 dev 11 function 0 (ToPIC95B), chipflags 2
cbb1 at pci0 dev 11 function 1 (ToPIC95B), chipflags 2
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
opms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
lpt0 at isa0 port 0x378-0x37b irq 7
wss0 at isa0 port 0x530-0x537 irq 5 drq 1 drq2 1: CS4231 or AD1845
audio0 at wss0: half duplex, mmap
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
cbb0: interrupting at irq 11
cbb0: cacheline 0x0 lattimer 0x0
cbb0: bhlc 0x820000 lscp 0x10100
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 1 device 0 cacheline 0x0, lattimer 0x0
pcmcia0 at cardslot0
cbb1: interrupting at irq 11
cbb1: cacheline 0x0 lattimer 0x0
cbb1: bhlc 0x820000 lscp 0x20200
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 2 device 0 cacheline 0x0, lattimer 0x0
pcmcia1 at cardslot1
biomask ef5d netmask ef5d ttymask ffdf
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 targ 1 lun 0: <IOMEGA, ZIP 100, 10.V> SCSI0 0/direct removable
sd0: 98304 KB, 96 cyl, 64 head, 32 sec, 512 bytes/sect x 196608 sectors
IPsec: Initialized Security Association Processing.
uhci_device_bulk_transfer: not done, ii=0xf060dd60
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
ex0 at cardbus0 dev 0 function 0: 3Com 3c575B-TX Ethernet
ex0: interrupting at 11
ex0: MAC address 00:50:04:b5:a1:4f
tqphy0 at ex0 phy 0: 78Q2120 10/100 media interface, rev. 11
tqphy0: 10baseT, 100baseTX, auto
ex0: supplying EUI64: 00:50:04:ff:fe:b5:a1:4f
IP Filter: initialized.  Default = pass all, Logging = disabled
IP Filter: v3.3.5
ex0: starting DAD for fe80:000b::0250:04ff:feb5:a14f
ex0: DAD complete for fe80:000b::0250:04ff:feb5:a14f - no duplicates found
uhci_device_request: not done, ii=0xf060dd20